Impeller | 340 BN/MB BTU Energy Transmitter

340 BN/MB BTU Energy Transmitter

The 340 BN/MB BTU Energy Transmitter is an economical, compact device for sub-metering applications using the BACnet or Modbus® communications protocol.

Showing units in {{labelText}}

Temperature Range

0...70 °C

32...158 °F

Request a quote

An economical, compact device for sub-metering applications.

Calculates thermal energy using the signal from a flow sensor installed in a hydronic heating or chilled water system, and the signals from two 10 kΩ temperature thermistors, 100 Ω RTDs or 1000 Ω RTDs installed in the system’s inlet and outlet points.

On-board microcontroller and circuitry make precise measurements and produce accurate, drift-free outputs
Calibration information for the flow sensor type and pipe size may be preselected or entered by the user in the field
Calculates thermal energy using the signal from a flow sensor installed in a hydronic heating or chilled water system
Compact cast epoxy body

Specifications

Download CSI Specifications

Showing units in {{labelText}}

Power Supply Options

Power supply: 12…24V AC | 12…35V DC
Current draw: 115 mA max. at 12V DC

Pulse Type Sensors - Signal Amplitude

2.5V DC threshold

Pulse Type Sensors - Signal Limits

Vin < 12V (DC or AC peak)

Pulse Type Sensors - Frequency Range

4…1000 Hz

Pulse Type Sensors - Pull-up

15V DC @ 2k Ω source Impedance

Sine Wave Sensors - Signal Amplitude

30 mV p-p threshold

Sine Wave Sensors - Signal Limits

Vin < 12V (DC or AC peak)

Sine Wave Sensors - Frequency

4…1000 Hz

Power Out Terminal

15V DC ± 1V DC @ 500 Ω source Impedance

Temperature Sensor (2 of same type required) Input

• 10k Ω thermistor, 2 wire, type II, 10k Ω @ 25° C (77° F)
• 100 Ω platinum RTD, DIN calibration curve, conforms to IEC-751 Standard
• 1000 Ω platinum RTD, DIN calibration curve, conforms to IEC-751 Standard
Calibration range of measurement 0…150° C (32…302° F)

Communication Port

RS-485 with termination, pull-up and pull-down jumpers

Pulse Output

Isolated solid-state switch in any standard or custom total units
Adjustable 50 ms to 1.0 second pulse output width in 50 ms increments
Maximum sinking current: 100 mA @ 36V DC

Isolated solid-state switch in any standard or custom total units
Adjustable 50 ms to 1.0 second pulse output width in 50 ms increments
Maximum sinking current: 100 mA @ 36V DC

Temperature

Operating: 0…70 °C
Storage: – 40…85 °C

Operating: 32…158 °F
Storage: – 40…185 °F

Weight

4.8 oz with connector headers installed

Sensor Calibration

Badger Meter: Use K and offset values provided in sensor manual
Other Sensors: Check with respected manufacturer of flow sensor and with factory

Units of Measure - Flow Measurement

Rate: gpm, gph, l/sec, l/min, l/hr, ft3/sec, ft3/min, ft3/hr, m3/sec, m3/min, m3/hr
Total: Gallons, Gallons X 100, Gallons X 1000, Liters, Cubic Feet, Cubic Meters

Units of Measure - Energy Measurement

Rate: kBtu/min, kBtu/hr, kW, MW, hp, tons
Total: Btu, kBtu, MBtu, kWh, MWh, kJ, MJ

Temperature Measurement

Fahrenheit, Centigrade

Programming

Requires PC or laptop running Windows 2000, XP, Vista or Windows 7
Data Industrial 340BN/MB Programming Kit A-301-20 containing software and Data Industrial Series programming cable is required for programming and setup

Requires PC or laptop running Windows 2000, XP, Vista or Windows 7
Data Industrial 340BN/MB Programming Kit A-301-20 containing software and Data Industrial Series programming cable is required for programming and setup

View all Specifications

340 BN/MB BTU Energy Transmitter

340 BN/MB BTU Energy Transmitter

An economical, compact device for sub-metering applications.

Specifications

Market Applications

Product Documentation

We’re sorry, your request didn’t return any documents.

Software & Firmware

We’re sorry, your request didn’t return any software or firmware.

Parts & Accessories